Table of Contents
Formica Build Instructions
Elaborated instructions for building a formica robot. If the part is on the top (with the printed names) or on the bottom (without the printed names) side is noted on the List of Parts.
Also necessary are the layouts for the top and the bottom side of the PCB.
Tools You Need
You will need a variety of tools to build a Formica:
- soldering iron
- fine tip and a bigger tip
- solder wick
- wire cutter
- double sided tape
For the microcontrollers a solder tip with a cavity is helpful
Soldering SMD parts
Most parts of the formica are surface mounted.
What you need to know about smd soldering for building a formica robot:
Some general instructions for smd soldering can be found here:
First populate the IC1 (MSP 430) and the IC2 (Battery Charger).
These chips have many pins and there are three basic methods for soldering them:
- Use a fine tip and solder each pin separately
- Use a bigger tip, solder all pins at once and remove the excessive solder with the solder wick.
- Use a special tip which contains a little cavity for solder.
We recommend the later method as it produces the best result. If you don't have one of these special tips for your soldering iron the next best method is using the big tip.
Careful with the orientation, the marking on the controller has to show in the same direction as given on the PCB. You can be quite generous with the flux here.
Again keep the orientation in mind. On each side two pins are connected with a solder bridge. If more are connected use the solderwick to remove the solder bridges. This can get easier if you first add some more solder to the bridge.
other smd stuff with more than two legs
Now most of the other smd parts with more than two pins will be populated.
If you haven't been using it already change to the small solder tip now.
Q3, Q2, Q1
On this side there are no markings for the orientation, so have a look at the layouts or orient on the pictures.
Q4, Q5, Q6, Q7, Q8, Q9
Special attention is necessary when soldering Q7 and Q8. I recommend starting with Q7, the pin next to R18.
C8, C9, C10
C1, C2, C3, C4
C5, C6, C7
The resistors are sometimes so close that you can't see at first glance which two pads will be connected by the resistor. Better check twice ;)
Some resistors are connected parallel and therefore their pads are connected. So sometimes the solderbridges are on purpose. If you're not shure check on an empty PCB.
R8, R9, R10, R11, R12, R13, R14, R15, R16, R17
R5, R6, R7, R24, R25
R1, R2, R3, R4
I reccomend changing to a bigger tip after soldering LED1,2,3
LED1, LED2, LED3
Position the LEDs so the circular part points away from the PCB (that's the actual LED, which will be used for communication between the robots)
After soldering the switch you should be careful with the vise, there is an overlap, don't break the switch.
PD1, PD2, PD3
Optional. These Parts offer the possibility to experiment with different materials and shapes of legs.
Remove the plastic. So now you have 4 parts instead of two.
If you haven't changed yet - now you will have to use the big tip.
Make shure that the front side is pointing away from the PCB. Make a good connection between the part an the solder. The sides should be parallel to the border of the PCB or there will be short cirquits. Attach the inner parts first.
One of the corners of the sensor is flattened a bit. This corner points towards the switch (have a look at the picture).
You can bend the connectors a little more away from the motors (without breaking them…). Now add some solder in the middle of the outer pad. Attatch the motor with an angle of about 30° between the PCB and the motor. Now attach the other contact.
For the second motor do the same. The angle doesn't have to be exactly the same, the connectors give in a bit.
If you haven't done it before cut alle the legs on the bottom side of the PCB to make room for the battery (even the short legs of the switch).
Cut the wires of the battery a bit, so they are about 2cm long. Solder the contacts on. Red wire goes to B+, black wire to B-.
Be careful, never shortcircuit the contacts on the battery!
Now put some double sided tape on the PCP and attach the Battery.
Sometime now or after flashing the formica you can put some wheels on the motors and put in the contacts you want to have.
And now its time to flash the robots.